Fruit

新建网页 9 2.99HP Straw Root Vegetable Fruit Grinder 220V Banana Tree Shredder Slicer Machine ≥600KG/H This machine is suitable for banana tree, banana tree, sweet potato, radish, potato, carrot, sweet potato vine, potato vine, grass, green corn stalk, yellow bamboo grass and other plants slicing or shredding. Processed feed is easier to store. It is a necessary machine for farmers, small and medium-sized feed processing plants and farms. At the same time, the machine can also be used with the feed granulator to facilitate the feed machine to form feed into pellets. Note: 1. Run for 2-5 minutes before operation, check whether the rotating speed meets the requirements of the machine, never allow overspeed, and check whether other parts are abnormal. If everything is normal, the feeding can be started, and the feeding cannot be excessive, so as to prevent damage to the supporting power unit and machine parts due to overload operation. 2. When the machine is operating, it is forbidden to stand at the grass outlet to prevent flying objects from hurting the body. 3. Operators are not allowed to wear gloves, sleeves must be fastened, and those with long hair must wear safety helmets. All personnel must leave the rotating plane of belt and rotating parts. 　 Product Material： Cast iron spray painting Production efficiency: ≥600KG/H Power: 2.2KW voltage： 220V Applicable Industries: Farms, Home Use The machine is equipped with a large feed port for easy feed handling. This machine is equipped with air switch, which is safer and more secure. This machine is equipped with a voltage display screen for a more intuitive reference to whether the voltage is stable.　 This machine is equipped with high-quality high-power motor. This machine is equipped with 4 moving casters, which is more convenient to move. (Can be disassembled and put down without using moving casters) Precautions for operation： In order to ensure the safety and normal operation of the person and the machine, a special person shall be assigned to be responsible for the storage and use of the machine. The machine shall not be operated without learning this procedure and operation technology and reading the familiar instructions. 1. In addition to commissioning according to the commissioning method, before starting, the machine must be carefully checked to see if there are tools and objects hindering the startup and operation, and whether the upper casing is locked. 2. Before starting the machine, it is necessary to check whether there are sundries in the machine. Except for processing straw, nothing is allowed to be stacked on the feeding table. 3. Check whether the electrical equipment is normal and safe. 4. The staff should not touch the operating parts, let alone open the casing and remove the safety cover. 5. Run for 2-5 minutes before operation, check whether the rotating speed meets the requirements of the machine, never allow overspeed, and check whether other parts are abnormal. If everything is normal, the feeding can be started, and the feeding cannot be excessive, so as to prevent damage to the supporting power unit and machine parts due to overload operation. 6. Feed crops evenly, not too much, so as not to block the feed inlet. The operator's hand shall not be close to the feeding belt during operation. 7. In case of blockage, stop the machine immediately. After the machine stops stably, open the upper cover, clean the blockage, and then restart. 8. Always pay attention to whether there is abnormal sound during the operation of the machine. Shut down and power off immediately in case of abnormality. 9. There shall be no mortar, sand, stone, iron wire, tool parts or other sundries in the crops to be processed to avoid damage to the machine or accidents. 10. At the end of each shift, the power supply must be cut off after all the crops on the feeding table are fed and no more materials are thrown out at the outlet. 12. When the machine is operating, it is forbidden to stand at the grass outlet to prevent flying objects from hurting the body. 13. Operators are not allowed to wear gloves, sleeves must be fastened, and those with long hair must wear safety helmets. All personnel must leave the rotating plane of belt and rotating parts. 　 　 Different places have different Receptacles. Please note this plug and consult your electrician before purchase. Note: We suggest that high-power machines should be directly connected to the main power supply, as the voltage reaching the machine is stable. If the voltage is unstable and the current exceeds the rated current of the motor, it is easy to burn out the starting capacitor. It is recommended to directly connect to the power supply as much as possible. If the machine is not connected to the power supply, different situations may occur, and the wires are not durable. The wires will gradually burn out over time. 　On Apr 24, 2024 at 00:55:02 PDT, seller added the following information: